Коды ошибок Kyocera

В разделе коды ошибок Kyocera рассмотрены наиболее часто встречаемые ошибки Kyocera. Данная информация так же содержится в сервисной инструкции к любому принтеру или МФУ Kyocera. По вопросам получения инструкции или консультации по ошибке можно обратиться в сервисный центр Kyocera по телефону +38 093 870 4000 или написав письмо на info@vital-trade.com.ua.

Если в перечне нет нужной информации - наши инженеры помогут с решением Вашей проблемы.


Error Code Description To enter Service Mode To Execute Service Checks
C0030 Fax Control PWB System Problem. Processing with the optional fax software was disabled due to a hardware problem. Turn power Off/On. 1) Repl fax control PWB.
C0070 Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software. Turn power Off/On. 1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.
C0100 Backup Memory Device Error. Defective flash memory or defective control PWB. Turn power Off/On. 1) Replace the control PWB.
C0120 MAC Address Data Error. Defective flash memory. Turn power Off/On. 1) Replace the control PWB.
C0130 Backup Memory Read/Write Error. Defective flash memory or defective control PWB. Turn power Off/On. 1) Replace the control PWB.
C0140 Backup Memory Data Error. Defective flash memory or defective control PWB. Turn power Off/On. 1) Replace the control PWB.
C0150 Control PWB EEPROM Error. Detecting control PWB EEPROM (U17) communication error. Turn power Off/On. 1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.
C0170 Billing Counting Error. Defective control PWB or its EEPROM (U17). Turn power Off/On. 1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.
C0180 Machine Number Mismatch Error. Machine number does not match on main and engine PWBs. Turn power Off/On. 1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB, 3) Repl engine PWB.
C0420 Paper Feeder Communication Error. Communication error between the control PWB and optional paper feeder. Turn power Off/On. 1) Incorrect installation-reinstall, 2) Reseat YC30 @ control PWB & paper feeder interface connector, 3) Reseat YC5 @ control PWB & paper feeder interface connector, 4) Repl interface harness, 5) Repl control PWB, 6) Repl PF main PWB.
C0830 Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB. Turn power Off/On. 1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.
C0840 Faults of RTC. The time is judged to go back based on the comparison of the RTC time and the current time, or (5) years or more have passed. Turn power Off/On. 1) Reinstall the backup battery on the fax control PWB, 2) Repl fax control PWB.
C0870 Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High-capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried several times. Turn power Off/On. 1) Reinstall the fax control PWB, 2) Repl fax control PWB, 3) Repl control PWB.
C0920 Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB. Turn power Off/On. 1) Repl fax control PWB.
C2000 Main Motor Error. The main motor ready input is not given for 2 sec, after the main drive motor has turned On. Turn power Off/On. 1) Reseat drive motor connector CN1 & control PWB connector YC17, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl main motor, 5) Repl control PWB.
C2610 PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 1) Turn power Off/On. 1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.
C2620 PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 2) Turn power Off/On. 1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.
C3100 ISU Home Position Error. Home position is not correct when power is turned On, or copying a document from the contact glass. Turn power Off/On. 1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between ISU motor & YC104 @ scanner PWB, 4) Replace FFC from YC6 to YC103, 5) Replace FFC from ISU motor to YC104, 6) Check/repl scanner HPS, 7) Check scanner drive components for excessive drag, 8) Repl scanner motor, 9) Repl image scanner unit (ISU).
C3200 Exposure Lamp Error. The exposure lamp is not turned On. Turn power Off/On. 1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between YC3 @ CCD PWB & YC101 @ inverter PWB, 4) Reseat FFC between YC102 @ inverter PWB & exposure lamp, 5) Replace FFC from YC6 to YC103, 6) Replace FFC from YC3 to YC101, 7) Replace FFC from inverter to exposure lamp, 8) Repl exposure lamp, 9) Repl inverter PWB, 10) Repl image scanner unit (ISU).
C3300 AGC Error. After AGC the correct input is not obtained at the CCD. Turn power Off/On. 1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).
C3500 CPU-ASIC (CCD PWB) Communication Error. An error code is detected. Turn power Off/On. 1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).
C4000 Polygon Motor Error. Polygon motor ready input is not given for 6 sec while the polygon motor is On. Turn power Off/On. 1) Reseat polygon motor connector & YC10 @ control PWB, 2) Repl polygon motor harness, 3) Repl laser unit, 4) Repl control PWB.
C4200 Beam Detect Error. BD sensor does not detect the laser beam. Turn power Off/On. 1) Possible condensation on polygon mirror. Clean or repl laser unit. 2) Reseat laser unit connectors, 3) Repl laser unit, 4) Repl control PWB.
C6000 Broken Fuser Heater Wire. The temperature does not rise after the fuser heater lamp is turned On. Turn power Off/On. 1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
C6020 Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects abnormally high temperature. Turn power Off/On. 1) Ohm out thermistor. If 0 ohms replace, 2) Repl control PWB.
C6030 Broken Fuser Thermistor Wire.Input from fuser thermistor is 0 (A/D value). Turn power Off/On. 1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
C6400 Zero-Cross Signal Error. The zero cross signal does not reach the control PWB for a specified time. Turn power Off/On. 1) Check wall outlet ground to neutral voltage. 2) Reseat YC202 @ high voltage PWB & YC23 @ control PWB, 3) Reseat YC103 @ PSU & YC201 @ high voltage PWB, 4) Repl harness from YC202 to YC23, 5) Repl harness from YC103 to YC201, 6) Check YC103-8 @ PSU for zero-crossing signal. If absent repl PSU, 4) If zero-crossing signal is present repl control PWB.
C7990 Waste Toner Full. The waste toner sensor has detected that the waste toner reservoir (drum unit) is full. Turn power Off/On. 1) Shake process unit side to side, then power Off/On, 2) Repl drum unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl control PWB.
F000 Control PWB-Operation panel PWB comunication error. Turn power Off/On. 1) Reseat YC1 @ operation panel PWB & YC7 @ control PWB, 2) Repl harness from YC1 to YC7, 3) Repl operation panel PWB, 4) Replace control PWB.
F020 Control PWB RAM Checksum Error. Defective main RAM on the control PWB or defective expanded memory DIMM. Turn power Off/On. 1) Power Off/On, 2) Repl expanded memory DIMM, 3) Replace control PWB. Contact Service Administrative Division.
F040 Control PWB Engine Communication Error. Turn power Off/On. 1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.
F041 Control PWB-Scanner PWB Communication Error. A communication error is detected. Turn power Off/On. 1) Power Off/On, 2) Replace control PWB, 3) Repl scanner PWB. Contact Service Administrative Division.
F050 Control PWB Engine Checksum Error. Some error may have occurred while downloading firmware, or defective control PWB. Turn power Off/On. 1) Reload current firmware, 2) Power Off/On, 3) Replace control PWB. Contact Service Administrative Division.
F186 Control PWB Video Data Control Error. Turn power Off/On. 1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.
E00000 or U00000 Fax Communication Error: No response or line busy after the set number of redials. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00100 or U00100 Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00200 or U00200 Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00300 or U00300 Fax Communication Error: Recording paper on the destination unit has run out during reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Load paper.
E00420 or U00420 Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00421 or U00421 Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00430 or U00430 Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00430 or U00430 Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00431 or U00431 Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00431 or U00431 Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00432 or U00432 Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00432 or U00432 Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00433 or U00433 Fax Communication Error: Confidential polling request was received but data was not present in the confidential box. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00433 or U00433 Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00434 or U00434 Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00435 or U00435 Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00435 or U00435 Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00440 or U00440 Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00440 or U00440 Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00440 or U00440 Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00441 or U00441 Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00450 or U00450 Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00460 or U00460 Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00460 or U00460 Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00462 or U00462 Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00500 or U00500 Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00600 or U00600 Fax Communication Error: The document processor cover is open. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00601 or U00601 Fax Communication Error: Document jam or the document length exceeds the maximum. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00602 or U00602 Fax Communication Error: Image scanning section problem. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00603 or U00603 Fax Communication Error: No document feed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00604 or U00604 Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00610 or U00610 Fax Communication Error: Recording section cover open. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00611 or U00611 Fax Communication Error: Recording paper jam. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00613 or U00613 Fax Communication Error: Image writing section problem. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00614 or U00614 Fax Communication Error: Nearly empty of recording paper. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00615 or U00615 Fax Communication Error: Empty of recording paper. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00620 or U00620 Fax Communication Error: Copier fixing unit problem. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00622 or U00622 Fax Communication Error: Copier drive motor problem. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00655 or U00655 Fax Communication Error: CTS was not activated after RTS due to a modem error. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00656 or U00656 Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00670 or U00670 Fax Communication Error: Power was cut off during communication. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00677 or U00677 Fax Communication Error: There was no file to transmit in the memory transmission mode. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00690 or U00690 Fax Communication Error: System error. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00700 or U00700 Fax Communication Error: Communication was interrupted because of a problem in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00800 or U00800 Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E00810 or U00810 Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode. Exxxxx: V.34 modem, Uxxxxx: all other modems
E00900 or U00900 Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E00910 or U00910 Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode. Exxxxx: V.34 modem, Uxxxxx: all other modems
E01000 or U01000 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01000 or U01000 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01001 or U01001 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01010 or U01010 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01011 or U01011 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01012 or U01012 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01013 or U01013 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01014 or U01014 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01015 or U01015 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01016 or U01016 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01017 or U01017 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01018 or U01018 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01019 or U01019 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01020 or U01020 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01021 or U01021 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01022 or U01022 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01023 or U01023 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01024 or U01024 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01025 or U01025 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01026 or U01026 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01027 or U01027 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01028 or U01028 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01040 or U01040 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01041 or U01041 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01042 or U01042 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01043 or U01043 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01044 or U01044 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E010x45 or U01045 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01046 or U01046 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01047 or U01047 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01048 or U01048 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01049 or U01049 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01050 or U01050 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01051 or U01051 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01052 or U01052 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01053 or U01053 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01054 or U01054 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01055 or U01055 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01056 or U01056 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01057 or U01057 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01070 or U01070 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01071 or U01071 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01072 or U01072 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brake in loop current was detected during transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01073 or U01073 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01080 or U01080 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01091 or U01091 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01092 or U01092 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01100 or U01100 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01101 or U01101 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01102 or U01102 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01110 or U01110 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01111 or U01111 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01112 or U01112 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01113 or U01113 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01114 or U01114 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01115 or U01115 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01116 or U01116 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01117 or U01117 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01118 or U01118 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01119 or U01119 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01120 or U01120 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01121 or U01121 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01122 or U01122 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01123 or U01123 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01124 or U01124 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01125 or U01125 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01126 or U01126 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01127 or U01127 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01128 or U01128 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01129 or U01129 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01140 or U01140 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01141 or U01141 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01142 or U01142 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01143 or U01143 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01144 or U01144 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01145 or U01145 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01146 or U01146 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01147 or U01147 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01148 or U01148 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01149 or U01149 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIP signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01150 or U01150 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01151 or U01151 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01152 or U01152 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01153 or U01153 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01154 or U01154 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RNR signal (ECM). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01155 or U01155 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol). Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01160 or U01160 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01161 or U01161 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01162 or U01162 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01163 or U01163 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01164 or U01164 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01170 or U01170 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01172 or U01172 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01191 or U01191 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01199 or U01199 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01400 or U01400 Fax Communication Error: An invalid one-touch key was specified during communication. Exxxxx: V.34 modem, Uxxxxx: all other modems Check the programming of the appropriate one-touch key.
E01500 or U01500 Fax Communication Error: A communication error occurred when calling in V.8 mode. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01600 or U01600 Fax Communication Error: A communication error occurred when called in V.8 mode. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01700 or U01700 Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01720 or U01720 Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01721 or U01721 Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01800 or U01800 Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01810 or U01810 Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01820 or U01820 Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E01821 or U01821 Fax Communication Error: Operation was interrupted due to the absence of a common communication speed between units. (including when an impossible combination of communication speed and symbol speed occurs) after MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E02000 or U02000 Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used. Exxxxx: V.34 modem, Uxxxxx: all other modems
E02100 or U02100 Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability. Exxxxx: V.34 modem, Uxxxxx: all other modems
E02200 or U02200 Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified. Exxxxx: V.34 modem, Uxxxxx: all other modems
E02200 or U02200 Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified. Exxxxx: V.34 modem, Uxxxxx: all other modems
E02200 or U02200 Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted. Exxxxx: V.34 modem, Uxxxxx: all other modems
E02303 or U02303 Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E02304 or U02304 Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received. Exxxxx: V.34 modem, Uxxxxx: all other modems Poor line conditions. Contact local phone provider.
E02400 or U02400 Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03000 or U03000 Fax Communication Error: No document was present in the destination unit when polling reception started. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03100 or U03100 Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03200 or U03200 Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03200 or U03200 Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03300 or U03300 Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03300 or U03300 Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03400 or U03400 Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03500 or U03500 Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03500 or U03500 Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03500 or U03500 Fax Communication Error: The destination was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03600 or U03600 Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03600 or U03600 Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03700 or U03700 Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E03700 or U03700 Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04000 or U04000 Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04000 or U04000 Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04000 or U04000 Fax Communication Error: The destination was being accessed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04100 or U04100 Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04100 or U04100 Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04200 or U04200 Fax Communication Error: In encrypted transmission, the specified encryption box was not registered in the destination unit. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04300 or U04300 Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04400 or U04400 Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04401 or U04401 Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered. Exxxxx: V.34 modem, Uxxxxx: all other modems
E04500 or U04500 Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys. Exxxxx: V.34 modem, Uxxxxx: all other modems
E05000 or U05000 Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals. Exxxxx: V.34 modem, Uxxxxx: all other modems
E05100 or U05100 Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match. Exxxxx: V.34 modem, Uxxxxx: all other modems
E05200 or U05200 Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E05300 or U05300 Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number. Exxxxx: V.34 modem, Uxxxxx: all other modems
E09000 or U09000 Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine. Exxxxx: V.34 modem, Uxxxxx: all other modems
E12000 or U12000 Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception. Exxxxx: V.34 modem, Uxxxxx: all other modems
E12000 or U12000 Fax Communication Error: In subaddress-based relay reception memory overflowed. Exxxxx: V.34 modem, Uxxxxx: all other modems
E12100 or U12100 Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station). Exxxxx: V.34 modem, Uxxxxx: all other modems
E14000 or U14000 Fax Communication Error: Memory overflowed during confidential reception. Exxxxx: V.34 modem, Uxxxxx: all other modems
E14000 or U14000 Fax Communication Error: Memory overflowed in subaddress-based confidential reception. Exxxxx: V.34 modem, Uxxxxx: all other modems
E14100 or U14100 Fax Communication Error: Memory overflowed in the destination unit during confidential transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems
E14100 or U14100 Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems
E19000 or U19000 Fax Communication Error: Memory overflowed during memory reception. Exxxxx: V.34 modem, Uxxxxx: all other modems
E19100 or U19100 Fax Communication Error: Memory overflowed in the destination unit during transmission. Exxxxx: V.34 modem, Uxxxxx: all other modems
E19200 or U19200 Fax Communication Error: Memory transmission failed because a decoding error occurred. Exxxxx: V.34 modem, Uxxxxx: all other modems
E19300 or U19300 Fax Communication Error: Transmission failed because an error occurred during JBIG encoding. Exxxxx: V.34 modem, Uxxxxx: all other modems
E19400 or U19400 Fax Communication Error: Reception failed because an error occurred during JBIG encoding. Exxxxx: V.34 modem, Uxxxxx: all other modems
message "Add Toner." 1) Replace toner container.
message "Cannot connect to Authentication Server." Press OK key. 1) Check registration to Authentication server. 2) Check password and computer address for Authentication Server. 3) Check connection to network.
message "Cannot duplex print on this paper." 1) To print without using duplex press OK. 2) Select the available paper type.
message "Cannot send fax." 1) Cord connected? Check phone cord. 2) Is the permitted fax # or permitted ID # registered correctly? Check. 3) Has a communication error occurred? See above. 4) Is the destination fax line busy? Send again. 5) Does the destination fax machine respond? Send again. 6) Is there an error other than above? See above.
message "Close Document Processor." 1) The document processor is still open even though an original has been inserted. Close the document processor. 2) Close the top cover of the document processor.
message "Close front cover." 1) The top cover or the front cover is open. Close the covers securely.
message "Error occurred. Turn the main power switch off and on. C####" Turn power Off/On. 1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
message "File is not found. Job is cancelled." 1) The specified file is not found. The job is cancelled. Press the OK key.
message "Incorrect account ID. Job is cancelled." 1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
message "Incorrect account ID." 1) The Account ID does not match. Check the registered Account ID.
message "Incorrect Login User Name or Password. Job is cancelled." 1) Enter the correct login user name or password.
message "Insufficient memory. Cannot start the job." 1) Further scanning cannot be performed due to insufficient memory. Press the OK key to print the scanned pages. Press the Cancel key to cancel the printing job.
message "Job Accounting restriction exceeded. Cannot print." 1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
message "Job Accounting restriction exceeded. Cannot scan." 1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
message "Job Accounting restriction exceeded. Job is cancelled." 1) The printing count exceeded the acceptable count restricted by Job Accounting. Cannot print any more. This job is cancelled. Press the OK key.
message "Load paper in MP Tray" 1) The paper has run out. Add paper to the paper source.
message "Load paper to cassette 1" 1) The paper has run out. Add paper to the paper source, 2) The cassette is not properly closed. Be sure the cassette it closed securely.
message "Machine failure. Call service. C####" Turn power Off/On. 1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
message "Memory is full. Print job cannot be processed completely." 1) Unable to continue the job as the memory is used up. Press the OK key to print the scanned pages. The print job cannot be processed completely. Press the Cancel key to cancel the job.
message "Paper jammed." 1) If a paper jam occurs the machine will stop and the location of the jam will be indicated on the Message Display. Leave the machine On and follow the instructions to removed the jammed paper.
message "Place original and press Start key." 1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.
message "Remove original from Document Processor." 1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.
message "Scanner memory is full. Job is cancelled." 1) Scanning cannot be performed due to insufficient memory of scanner. The job is cancelled. Press the OK key.
message "Send error. ####" 1) See below:
message "Sub address/Polling box limit exceeded. Job is cancelled." 1) Fax box is full and no further storage is available. The job is cancelled. Press the OK key.
message "The phone receiver is off the hook. Hang up." 1) Put down the receiver.
message "Top tray is full of Paper. Remove the paper." 1) Remove the paper from the top tray, and press the OK key to resume the job.
message "Unknown toner installed. PC" 1) This message is displayed if the installed toner container's regional specification does not match the machine's.
message "Unknown toner installed." 1) If the toner container was taken from a different machine of the same model while it was displaying the Add Toner message, ignore the message and use the toner.
message "USB memory error. Job is cancelled." 1) This job is cancelled. Press the OK key.
Send Error 1101 Error: FTP Host Name. Enter the disable host name/IP address. Send errors are displayed on the panel only, and not recorded. Enter the correct host name or IP address.
Send Error 1101 Error: Host Name. SMTP server name is not set. Error SMTP server name. Send errors are displayed on the panel only, and not recorded. Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign disable SMB shared name. Send errors are displayed on the panel only, and not recorded. Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign disable SMB user/password. Send errors are displayed on the panel only, and not recorded. Enter the correct username/password.
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign the SMB user who is not allowed to access the folder. Send errors are displayed on the panel only, and not recorded. Enter the correct username/password. Check the access limit of destination folder.
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered. Send errors are displayed on the panel only, and not recorded. Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered. Send errors are displayed on the panel only, and not recorded. Scan folder is not shared out to the network properly.
Send Error 1102 Error: Username/Password or Shared Name/Folder Name. SMB host name error. Send errors are displayed on the panel only, and not recorded. Check if the prohibited letters are used to shared name: "&'()`;<>
Send Error 1102 Error: Username/Password. Assign disable FTP user/password. Send errors are displayed on the panel only, and not recorded. Enter the correct username/password.
Send Error 1102 Error: Username/Password. FTP domain name is not entered. Send errors are displayed on the panel only, and not recorded. Enter the user name with the form of either [DomainYUser] or [Domain/User].
Send Error 1102 Error: Username/Password. User ID for email authentication is not entered or entered wrongly. Wrong authentication password is entered. Send errors are displayed on the panel only, and not recorded. Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Send Error 1103 Error: Pathname or File Name. Assign disable FTP folder path. Send errors are displayed on the panel only, and not recorded. Enter correct folder path.
Send Error 1103 Error: Pathname or File Name. Assign disable SMB folder path. Send errors are displayed on the panel only, and not recorded. Enter correct folder path.
Send Error 1103 Error: Pathname or File Name. Connection to the FTP folder which is not permitted for reference/writing. Send errors are displayed on the panel only, and not recorded. Enter the correct username/password. Check the access limit of destination folder.
Send Error 1103 Error: Pathname or File Name. Connection to the SMB folder which is not permitted for reference/writing. Send errors are displayed on the panel only, and not recorded. Enter the correct username/password. Check the access limit of destination folder.
Send Error 1103 Error: Pathname or File Name. SMB domain name is not entered. Send errors are displayed on the panel only, and not recorded. Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Send Error 1104 Error: No Recipient Address. The destination email address is not specified. Send errors are displayed on the panel only, and not recorded. Specify the destination address.
Send Error 1105 Error: Not Supported Protocol. FTP protocol is set to OFF. Send errors are displayed on the panel only, and not recorded. Check ON in the [Scanner]-[FTP] screen in Command Center.
Send Error 1105 Error: Not Supported Protocol. SMB protocol is set to OFF. Send errors are displayed on the panel only, and not recorded. Check ON in the [Scanner]-[SMB] screen in Command Center.
Send Error 1105 Error: Not Supported Protocol. SMTP protocol is set to OFF. Send errors are displayed on the panel only, and not recorded. Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Send Error 1106 Error: No Sender Info. Sender email address is not entered. Send errors are displayed on the panel only, and not recorded. Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Send Error 2101 Error: Can Not Connect. Assign the wrong FTP port number. Send errors are displayed on the panel only, and not recorded. Enter the correct port number.
Send Error 2101 Error: Can Not Connect. Assign the wrong SMB port number. Send errors are displayed on the panel only, and not recorded. Enter the correct port number.
Send Error 2101 Error: Can Not Connect. Enter the disable FTP host name/IP address. Send errors are displayed on the panel only, and not recorded. Enter the correct host name or IP address.
Send Error 2101 Error: Can Not Connect. Enter the disable SMB host name/IP address. Send errors are displayed on the panel only, and not recorded. Enter the correct host name or IP address.
Send Error 2101 Error: Can Not Connect. Network FTP is not connected. Send errors are displayed on the panel only, and not recorded. Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2101 Error: Can Not Connect. Network SMB is not connected. Send errors are displayed on the panel only, and not recorded. Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2101 Error: Can Not Connect. Network SMTP is not connected. Send errors are displayed on the panel only, and not recorded. Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2101 Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP. Send errors are displayed on the panel only, and not recorded. Select valid POP3 user other than [Other].
Send Error 2101 Error: Can Not Connect. The specified server is not SMTP server. Send errors are displayed on the panel only, and not recorded. Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Send Error 2102 Error: Cannot Connect With Timeout. Send the server which does not support FTP server. Send errors are displayed on the panel only, and not recorded. Enter the correct host name or IP address.
Send Error 2102 Error: Cannot Connect With Timeout. The FTP server is unable to communicate. Send errors are displayed on the panel only, and not recorded. Check if the server is operating properly.
Send Error 2102 Error: Cannot Connect With Timeout. The SMTP server is unable to communicate. Send errors are displayed on the panel only, and not recorded. Check if the server is operating properly.
Send Error 2103 Error: Response Wait With Timeout. The FTP server is unable to communicate. Send errors are displayed on the panel only, and not recorded. Check is the server is operating properly.
Send Error 2103 Error: Response Wait With Timeout. The SMB server is unable to communicate. Send errors are displayed on the panel only, and not recorded. Check is the server is operating properly.
Send Error 2103 Error: Response Wait With Timeout. The SMTP server is unable to communicate. Send errors are displayed on the panel only, and not recorded. Check is the server is operating properly.
Send Error 2201 Error: FTP Network Transfer. Error occurs on the network. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2201 Error: SMB Network Transfer. Error occurs on the network. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2201 Error: SMTP Network Transfer. Error occurs on the network. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2202 Error: FTP Network Transfer With Timeout. Error occurs on the network. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2202 Error: SMTP Network Transfer With Timeout. Error occurs on the network. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2202 Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2202 Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2203 Error: Response Wait With Timeout. Response is not returned from the FTP server, above specified time. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2203 Error: Response Wait With Timeout. Response is not returned from the SMB server, above specified time. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2203 Error: Response Wait With Timeout. Response is not returned from the SMTP server, above specified time. Send errors are displayed on the panel only, and not recorded. Check the network connection (cable, network condition within LAN, etc.).
Send Error 2204 Error: Email Size Limit. The size of the email attachment exceeds its limit. Send errors are displayed on the panel only, and not recorded. Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Send Error 3101 Error: Server Response. SMTP server setting is not authenticated normally. Send errors are displayed on the panel only, and not recorded. Check the settings for client/server authentication.
Send Error 3101 Error: Server Response. The FTP server is error status. Send errors are displayed on the panel only, and not recorded. Check is the server is operating properly.
Send Error 3101 Error: Server Response. The SMTP server is error status. Send errors are displayed on the panel only, and not recorded. Check is the server is operating properly.
Send Error 3201 Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism found. Send errors are displayed on the panel only, and not recorded. Check the settings for client/server authentication mechanism.
Send Error 5101 Error: Send Software Not Yet Connected. Operation handle error. Error for stored status in the operation handle. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 5102 Error: Send Software Already Connected. Operation handle error. Error for stored status in the operation handle. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 5103 Error: Send Software Not Yet Opened. Error for storage status in the operation handle. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 5104 Error: Send Software Already Opened. Error for storage status in the operation handle. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 7101 Error: Send Software Memor Allocation. Insufficient memory space. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 7102 Error: Send Software Socket Create. Unable to create a communication socket. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 720f Error: Send Software Unknown Error. Unable to determine the cause. Power Off/On. Send errors are displayed on the panel only, and not recorded. Power Off/On.
Send Error 9181 Error: Email page Max Count Over. The number of pages of a send file exceeds 999 pages. Send errors are displayed on the panel only, and not recorded. Set the number of pages to 999 or less.
Send Error 9181 Error: FTP page Max Count Over. The number of pages of a send file exceeds 999 pages. Send errors are displayed on the panel only, and not recorded. Set the number of pages to 999 or less.
Send Error 9181 Error: SMB page Max Count Over. The number of pages of a send file exceeds 999 pages. Send errors are displayed on the panel only, and not recorded. Set the number of pages to 999 or less.
Send Error 9181 Error: TWAIN page Max Count Over. The number of pages of a send file exceeds 999 pages. Send errors are displayed on the panel only, and not recorded. Set the number of pages to 999 or less.

01.07.2015

© www.kyo.com.ua - интернет-магазин Kyocera в Украине 2012-2015. При копировании информации ссылка на источник обязательна.